Enmet SPECTRUM Uživatelský manuál Strana 1

ENMETENMETENMETENMET CorporationPO Box 979Ann Arbor, MI 48106-097980012-011December 1995MCN-153; 04/22/96MCN-157; 03/19/97MCN-172; 06/12/97MCN-187; 02

ENMET Corporation SPECTRUM Series62.1.6 Battery Status and Low Battery AlarmsThe battery status display is accessed by pressing the OPTION pushbutton

SPECTRUM Series ENMET Corporation73.0 Maintenance3.0 Maintenance3.0 Maintenance3.0 Maintenance3.1 Maintenance MenuFrom the operational display, press

ENMET Corporation SPECTRUM Series83.1.1 KeyEntrance to the maintenance menu is guarded with a four digit numerical key. The factory default setting o

SPECTRUM Series ENMET Corporation93.1.3 CalibrationNOTE: Calibration must be performed at normal room temperature (20-25°C) for optimal performance.

ENMET Corporation SPECTRUM Series103.1.5 Setting the Battery TypeA valid key entry sets the instrument at the "run ZERO" location of the mai

SPECTRUM Series ENMET Corporation113.2.2 Sensor Removal and ReplacementA low 9v battery may cause a “Cell Out” indication. Check or replace the 9v Ba

ENMET Corporation SPECTRUM Series124.0 Replacement Parts and Accessories4.0 Replacement Parts and Accessories4.0 Replacement Parts and Accessories4.0

SPECTRUM Series ENMET Corporation135.0 WARRANTY5.0 WARRANTY5.0 WARRANTY5.0 WARRANTYENMET warrants new instruments to be free from defects in workmansh

ENMET Corporation SPECTRUM Series14Appendix A: Calibration Data TablesAppendix A: Calibration Data TablesAppendix A: Calibration Data TablesAppendix A

SPECTRUM Series ENMET Corporation15Table 2: Spectrum Calibration Voltage and Countdown TimesNOTE: The following are values used for production calibra

ENMET Corporation SPECTRUM Series16Appendix B: Interference GasesAppendix B: Interference GasesAppendix B: Interference GasesAppendix B: Interference

SPECTRUM Series ENMET Corporation17SPECTRUM Series for CHLORINE (3E sensor)The following gases cause a reading:InterferantGas/VaporInterferant Concent

ENMET Corporation SPECTRUM Series18SPECTRUM Series for Hydrogen Chloride (3E 30 sensor)The following gases cause a reading:InterferantGas/VaporInterfe

SPECTRUM Series ENMET Corporation19SPECTRUM Series for Fluorine (3E 10 sensor)The following gases cause a reading:InterferantGas/VaporInterferant Conc

ENMET Corporation SPECTRUM Series20SPECTRUM Series for Nitric Oxide (3E 100 sensor)The following gases or vapors have been tested and do not cause a r

SPECTRUM Series ENMET Corporation21SPECTRUM Series for Ozone (3E 1 sensor)The following gases cause a reading:InterferantGas/VaporInterferant Concentr

ENMET Corporation SPECTRUM Series22SPECTRUM Series for Sulphur Dioxide(4S sensor)The following gases cause a reading:InterferantGas/VaporInterferant C

SPECTRUM Series ENMET Corporation23SPECTRUM Series for Phosgene (3E sensor)The following gases cause a reading:InterferantGas/VaporInterferant Concent

ENMET Corporation SPECTRUM Series24APPENDIX C APPENDIX C APPENDIX C APPENDIX C SPECTRUM for HydrazineSPECTRUM For HydrazineThe detection of hydrazine,

PO Box 979680 Fairfield CourtAnn Arbor, Michigan 48106-0979734.761.1270 Fax 734.761.3220Returning an Instrument for RepairENMET instruments may be ret

Table of Contents1.0 INTRODUCTION...

Repair Return FormMailing Address:ENMET CorporationPO Box 979Ann Arbor, Michigan 48106Phone Number: 734.761.1270FAX Number: 734.761.3220Shipping Addr

SPECTRUM Series ENMET Corporation11.0 Introduction1.0 Introduction1.0 Introduction1.0 IntroductionThe SPECTRUM is a small portable battery operated si

ENMET Corporation SPECTRUM Series21.2 Turn Instrument ONTurn the instrument ON, by pressing and holding the POWER / BACKLIGHT pushbutton for two secon

SPECTRUM Series ENMET Corporation32.0 Features and Operation2.0 Features and Operation2.0 Features and Operation2.0 Features and OperationThe features

ENMET Corporation SPECTRUM Series42.1 Operation2.1.1 Operational MenuThe operation menu flow diagram is shown in Figure 2. This menu is accessed with

SPECTRUM Series ENMET Corporation52.1.2 Turn ON and OFFTurn the instrument ON by pressing the POWER / BACKLIGHT pushbutton for two seconds. For most