Enmet TARGET Uživatelský manuál

ENMET CorporationPO Box 979Ann Arbor, MI 48106-0979Manual Part Number80012-014MCN-380, 11/07/07TARGET SeriesPortable Gas DetectorOperation & Maint

TARGET Series ENMET Corporation73.4.3 Over-range and Under-range AlarmsThe over-range alarm activates audio and visual alarms. It can occur if the

TARGET Series ENMET Corporation83.5.2 Calibration StatusThe TARGET instrument keeps track of the date of last calibration for each sensor. To view

TARGET Series ENMET Corporation93.5.5 Internal Sampling PumpIf the TARGET instrument has the optional internal sampling pump installed, the Pop-Up m

TARGET Series ENMET Corporation104.0 Basic User OperationThe TARGET instrument has two operation levels, BASIC and ADVANCED. The BASIC mode is inte

TARGET Series ENMET Corporation115.0 Advanced User OperationThe TARGET instrument has two operation levels, BASIC and ADVANCED. The BASIC mode is i

TARGET Series ENMET Corporation126.0 Maintenance Operations6.1 RecommendationsInstrument calibration should be performed at least once every three m

TARGET Series ENMET Corporation136.3.2 Zero AdjustThe calibration zero procedure is activated by pressing the SELECT button again. This starts a 30

TARGET Series ENMET Corporation14Figure 8: Various Calibration Adapter AttachmentsApply the span gas and press the SELECT button to initiate the sam

TARGET Series ENMET Corporation156.4 Advanced Maintenance Menu, Software 4.94 versionThe Advanced Maintenance menu provides access to enhanced progr

TARGET Series ENMET Corporation16button at the Exit line to go back to the Maintenance menu. STEL and TWA alarms are preset at the factory and cano

Table of Contents1.0 Introduction...

TARGET Series ENMET Corporation176.4.6 Set Battery TypeFrom the Advanced Maintenance menu, press the MENU button five times to put the asterisk next

TARGET Series ENMET Corporation186.4a Advanced Maintenance Menu, Software 6.0 versionThe Advanced Maintenance menu provides access to enhanced progr

TARGET Series ENMET Corporation19button at the Exit line to go back to the Maintenance menu. STEL and TWA alarms are preset at the factory and cano

TARGET Series ENMET Corporation206.5 Replacing Battery PackWARNING: Substitution of batteries or other components may compromise the intrinsic safet

TARGET Series ENMET Corporation216.7 Replacing SensorsWhen sensors can no longer be calibrated, they must be replaced. Replacing them is accomplish

TARGET Series ENMET Corporation227.0 Instrument Information7.1 Replacement Parts ListReplacement Parts:ENMET Part No. Description04835-000 Sampling

TARGET Series ENMET Corporation23Replacement Sensors:ENMET Part No. Description03008-131Sensor, BRHfor units with s/n 15-2499 and below03008-012 Sen

TARGET Series ENMET Corporation248.0 Default Alarm and ConfigurationsTable 3: Default AlarmGas Full ScaleDisplayResolution Alarm 1 Alarm 2 TWA STEL

TARGET Series ENMET Corporation259.0 Flow DiagramsTable 5: Target Menu Quick ReferenceBasic Operation:See section 9.1Main Gas Display; Date/Time/Bat

TARGET Series ENMET Corporation269.2 Standard Maintenance MenuEnter any calibration procedure from above:*Calibrate ExitCALIBRATION MENU*BRH O2/CO/H

6.5 Replacing Battery Pack...

TARGET Series ENMET Corporation279.3 Advanced Operation Menu02 20.9%CO 0ppm H2S 0ppmMth0%LEL BRH 0ppm*Date/Time/Batt Alarm Values Min / Max Values T

TARGET Series ENMET Corporation289.4 Advanced Maintenance Menu, Software 4.94 version*Calibrate Set Alarms Enable Sensors Set Clock/Chirp Calibrate*

TARGET Series ENMET Corporation299.4 Advanced Maintenance Menu, Software 6.0 version*Calibrate Set Alarms Enable Sensors Pump Cal Exit Calibrate*Set

TARGET Series ENMET Corporation3010.0 TroubleshootingSymptom Possible Cause ActionUnit will not turn on. Dead battery Plug instrument into charger.

TARGET Series ENMET Corporation3111.0 WARRANTYENMET warrants new instruments to be free from defects in workmanship and material under normal use fo

PO Box 979680 Fairfield CourtAnn Arbor, Michigan 48106-0979734.761.1270 Fax 734.761.3220Returning an Instrument for RepairENMET instruments may be ret

Repair Return FormMailing Address:ENMET CorporationPO Box 979Ann Arbor, Michigan 48106Phone Number: 734.761.1270FAX Number: 734.761.3220Shipping Addr

TARGET Series ENMET Corporation11.0 Introduction1.1 Warnings and CautionsThe TARGET Series gas detectors are designed to detect hazardous atmospheri

TARGET Series ENMET Corporation2 ENMET either repairs or replaces damaged equipment and invoices the carrier to the extent of the liabilitycoverage

TARGET Series ENMET Corporation3See Figures 1 and 2Visual Alarms There are visual alarms for each of the gas sensors installed.Display 4 line by 20

TARGET Series ENMET Corporation42.4 Locations and Data loggingThe TARGET instrument has the ability to store users or location information and log e

TARGET Series ENMET Corporation53.2 Charging the BatteryWARNING: Never charge the TARGET instrument in a hazardous locationThe TARGET instrument has

TARGET Series ENMET Corporation6Table 1: Battery LifeNormal operation with standard sensorsA fully charged NiMH battery pack may provide up to 18 ho